
Na topboarden voor zowel S754 (De Nforce3 250gb) als de gehele S939 Nforce4 reeds heeft DFI nu ook een board waarin het S939 combineert met een AGP slot, de DFI NForce3 Ultra-D. Het board is gereleased op 13 juni en dus nog gloedje nieuw te noemen. Desondanks wat problemen waarvan verwacht word dat deze binnen afzienbare tijd verholpen worden met een bios update en de gunstige prijs lijkt de DFI Nforce3 Ultra-D weer een dijk van een moederbord te worden. Als 3 ![]() |
CPU • AMD Athlon 64 FX / Athlon 64 / Sempron • Socket 939 Chipset • nVIDIA® nForce3 Ultra Front Side Bus • 2000MT/s HyperTransport interface Memory • Four 184-pin DDR SDRAM DIMM sockets • Supports dual channel (128-bit wide) memory interface • Supports up to 4GB system memory • Supports PC2100 (DDR266), PC2700 (DDR333) and PC3200 (DDR400) DDR SDRAM DIMM BIOS • Award BIOS • CPU/DRAM/AGP overclocking • CPU/DRAM/Chipset overvoltage • 4Mbit flash memory • AMD Cool‘n’Quiet technology Power Management • Supports ACPI STR (Suspend to RAM) function • Wake-On-Events include: - Wake-On-PS/2 Keyboard/Mouse - Wake-On-Ring (external modem) - Wake-On-LAN - RTC timer to power-on the system • AC power failure recovery Hardware Monitor • Monitors CPU/system temperature • Monitors VCC3/5V/12V/5Vsb/Vbat voltages • Monitors the speed of the cooling fans • CPU Overheat Protection function monitors CPU temperature during system boot-up Audio • Realtek 6-channel audio CODEC • S/PDIF-in/out interface LAN • Gigabit PHY • Fully compliant to IEEE 802.3 (10BASE-T), 802.3u (100BASE-TX) and 802.3ab (1000BASE-T) standards IDE • Two IDE connectors support four UltraDMA 133Mbps hard drives • NVIDIA RAID allows RAID arrays spanning across Serial ATA and Parallel ATA • RAID 0, RAID 1, RAID 0+1 and JBOD Serial ATA with RAID • Four Serial ATA interfaces with speed up to 1.5Gbps - Two Serial ATA ports supported by nForce3 Ultra chip - Two Serial ATA ports supported by Marvell SATA PHY • NVIDIA RAID allows RAID arrays spanning across Serial ATA and Parallel ATA • RAID 0, RAID 1, RAID 0+1 and JBOD IEEE 1394 • VIA VT6307 controller • Supports two 100/200/400 Mb/sec ports AGP • Supports AGP 8x up to 2132MB/sec. and AGP 4x up to 1066MB/sec. bandwidth for 3D graphics applications • Supports 0.8/1.5V add-in cards Rear Panel I/O Ports • 1 PS/2 mouse port • 1 PS/2 keyboard port • 1 DB-25 parallel port • 2 S/PDIF RCA jacks (S/PDIF-in and S/PDIF-out) • 1 DB-9 serial port • 1 IEEE 1394 port • 1 RJ45 LAN port • 4 USB 2.0/1.1 ports • Line-in, line-out and mic-in jacks I/O Connectors • 2 connectors for 4 additional external USB 2.0/1.1 ports • 1 connector for 1 external IEEE 1394 port • 1 front audio connector for external line-out and mic-in jacks • 1 CD-in internal audio connector • 1 S/PDIF connector for optical cable connection • 1 IrDA connector • 4 Serial ATA connectors • 2 IDE connectors • 1 floppy connector • 1 20-pin ATX power connector • 1 4-pin ATX 12V power connector • 1 front panel connector • 3 fan connectors • EZ touch switches (power switch and reset switch) Expansion Slots • 1 AGP 8x/4x slot • 5 PCI slots PCB • ATX form factor • 30.5cm (12") x 24cm (9.44") ![]() |
![]() Met dank aan Sir_G-nius, en uiteraard zijn zusje van wie hij de camera heeft geleend ![]() |
Tweakers.net Pricewatch • DFI Nforce3 Ultra-D S939 Reviews • Helaas hebben we in de zeer beperkte tijd die we beschikbaar hadden geen waardige review gevonden om hier te posten. • Heb je er een gevonden, zoek dan even contact. ![]() |
Nubius @ DFI-Street mailde het volgende naar DFI, dit dekt de lading van fouten perfect... In de reply van DFI werd gesproken over de weerstand op het volgende plaatje, en dat er een bios uitkwam, en 'the board needs to be reworked' wat ze daar ook mee bedoelen... ![]() Hoot @ DFI-Street heeft deze weerstand eraf gesoldeert met het volgende resultaat: Waarschijnlijk behoort hier een andere weerstand te zitten om het voltage op de processor goed te krijgen. Hiermee is iedereen aardig op de hoogte qua fouten en vorderingen... ![]() |
Er is tot op heden nog maar een officieel uitgebrachte bios voor het moerdbord, en dat is de bios die reeds op je chippie geflashed staat Officiële biossen • 2005/06/02 • 2005/07/05 Enkele borden zijn al gesneuveld met de 2005/07/05... gijt zijt gewaarschuwed Beta biossen • 2005/06/28 ![]() |
Vdimm Mod For The DFI LanParty nF3 Ultra by Polygon @ RHCF.COM The DFI LanParty nF3 Ultra has what is known as a "Linear Regulator" type of power supply for the Vdimm power supply. This type of power supply is powered by the +3.3V bus from the PSU. Because of this, 3.3V is the theoretical maximum that the Vdimm power supply can deliver to the memory modules. In reality, because there are voltage drops in the circuit and across the FET, the actual Vdimm can only reach about 3.15V, depending on the actual +3.3V PSU voltage. I measured Vdimm using a Digital Multi-Meter. Here's what I got at each BIOS setting: VDIMM 2.5V = 2.58V 2.6V = 2.69V 2.7V = 2.80V 2.8V = 2.91V 2.9V = 3.00V 3.0V = 3.10V 3.1V = 3.16V 3.2V = 3.17V If one has a PSU with an adjustable +3.3V rail, that can be increased and the BIOS Vdimm maximums will start to fall in line with the other settings that are overvolting at this time. The mod is to attach the 3.3V rail to the Vdimm bus. Most memory just loves 3.3V, but will need additional cooling to benefit from this increased voltage. I recommend at least 1 80mm fan blowing directly on the memory modules. The first picture shows a detail of the FET so there's no confusion. Sometimes the center leg that is the Drain, is cut short. As the metal backside of the FET is also the Drain terminal, this doesn't matter. They are connected inside. Vdimm is available on the "Source" lead of the FET. Now this is where the PSU with the adjustable +3.3V rail comes in handy. With the mod in place, the Vdimm can be raised above 3.3V by using the PSU adjustment. Many adjustable PSU's can go to 3.5V and now memory with BH-5 or similar chips, will overclock well. The Vdimm bus is labeled in the 2nd picture and it is this point that gets connected to the +3.3V PSU bus. The Vdimm FET has the reference designation of Q38. The +3.3V bus is any orange wire in the ATX power connector. You can also trace the tracks of the orange wires to the backside of the motherboard, and solder to one of them. The wire that connects the +3.3V to the Vdimm should be at least #22 gauge as the current with 2 modules is easily around 1 ampere. The voltage the memory then will see will be 3.3V or whatever you have the +3.3V PSU rail adjusted to. This "Standard 3.3V Mod" has been around for a while, and can be found described on almost every OC forum for any DDRAM motherboard that uses a "Linear Regulator" type of power supply for generating Vdimm. ![]() As an alternate, a short wire can be solbered between the "Source" and the "Drain" pad on the motherboard. This would probably be a cleaner way of doing the Mod. ![]() Disclaimer and Warning Implementing this mod will void your boards warrantee and also may cause catastrophic failure to the board, CPU, and/or memory modules. Do not do this mod unless you are willing to accept this risk. ![]() |
• Laagvliegerke, voor wat gestolen code uit zijn DFI Nforce4 TS • Xiled, voor het proberen van de bios, waardoor wij nu weten dat we niet moeten updaten nog • Ephymerous, aanpassen, text, plaatjes There is more to come ![]() |
<!-- Aangezien de DFI LANParty UT nF3 Ultra-D (s939, agp) inmiddels wordt geleverd, en ik sterk overweeg om dit bordje aan te schaffen (ik heb een goede agp kaart en wil dus geen pci-e moederbord), ben ik benieuwd of er al eigenaren zijn die dit bordje hebben, en zo ja, wat hun ervaringen met OC zijn. -->
[ Voor 148% gewijzigd door Twynn op 14-07-2005 17:16 . Reden: Nieuwe topicstart ]