Dat had ik absoluut niet met de FFX, maar met de FnS en de laatste firmware weer wel, De de voorgaande firmware weer absoluut niet

(volg je het nog

)
Vraagje aan jullie nog: waar hebben jullie de sensitivity in de config tool op staan, low-med-high?
Ik kan hierover niet zoveel gegevens vinden namelijk. Slaat dit op de muis, of op de knoppen?
Slaat op de knoppen. Hoe gevoelig zijn de knoppen voor aanraking. Nu moet ik zeggen dat toen ik deze op high had staan, de knoppen ineens heel slecht reageerde. Weer teruggezet op medium en eigenlijk niet verder mee getest, dus low nog niet geprobeerd.
Hier staat overigens de manual. Hier staat ook dat je de CPI kan aanpassen, dit merk je direct als je m gebruikt op de PC, het schijnt ook merkbaar te zijn in combi met de PS3 (volgens Keith. Wie is Keith? Een van DE mannen van Bannco, in ieder geval degene die reageert op je eventuele support mails).
Om de CPI aan te passen moet je het volgende doen. De Fragnstein moet in PC modus staan, dwz dongle in je PC
zonder knopje indrukt te houden.
Eigenlijk de zelfde werkwijze om de F clicks in te stellen als de dongle in de PS3 zit.
FRAGnStein Resolution
To increase the Mouse resolution press and hold the F button and roll the mouse wheel forward.
To decrease the resolution press and hold the F button and roll the wheel backward.
There are four CPI mouse resolutions to choose from: 400, 800, 1200 and 1600. While you press and hold the F key to adjust the CPI, the mouse led will flash once when set to 400, twice for 800, three times for 1200 and four times for 1600. Press and hold the F button and the mouse light will repeat the flash amounts for setting resolutions. The resolution is stored in memory so it does not need to be set each time you use your controller.baronruud
Of je moet je DZ aanpassen.
Die deadzone instellingen kan ook maar weinig over vinden.
Ik neem aan dat je
dit wel heb gevonden op de site:
We have now added a dead zone adjustment to the firmware. When you install this firmware you will add the function on the mouse to adjust the dead zone and the mouse sensitivity.
We suggest that you first set your mouse to F0. F0 is the finest movements. To set your mouse to F0: Start your game and then pressing and hold the mouse F button. While holding the mouse F button roll the mouse wheel forward and back until the game just stops to roll to the right. That is F0 and F0 will be the most smooth for all games.
While holding the mouse F button you can now push the mouse wheel to the left to lower the dead zone and to the right to increase the dead zone. There are 8 dead zone settings.
The higher the dead zone is set, the faster the mouse will go. We suggest you first press the mouse wheel to the left 8 times to set the dead zone to 0. Now adjust the video game's controller speed to a med to med high setting. Now you will notice that adjusting the dead zone to the right will increase the mouse speed.
These are our suggested settings for all games:
Mouse F1: (mouse sensitivity) = one mouse click forward from when the game starts to roll.
Dead Zone: (mouse speed) DZ2 = Mouse Side wheel buttons two presses to the right.
Video Game Speed: Controller set to med to med high.
You will of course find the best settings according to your play style.baronruud
en firingspeed?
Dit heeft te maken met de auto fire function, handig (

) voor handguns. Dan kun je de muisknop gewoon ingedrukt houden om te schieten. Ik zelf gebruik het nooit. Het enige wat auto fire doet is het simuleren van het indrukken en loslaten van de muisknop met de snelheid die je daar in stelt. Maar dit doet ie dus ook voor je longguns en dan is het dus weer niet handig! Ik heb geen goede ervaringen met auto fire.
@direct hieronder
1600 het beste? Dat hangt helemaal van je eigen wensen af, 1600 is super gevoelig. 1 mm met je muis en de muiscursor op je pc scherm is aan de andere kant van het scherm. Ook hier zul je dus mee moeten experimenteren.
Voor elke instelling geldt: experimenteren totdat je de naar jou idee beste -wat jij het fijnst vind spelen- instellingen gevonden heb. Experimenteer ook weer niet te veel, op een gegeven moment moet je ook gewoon aan bepaalde instellingen wennen/acclimatiseren.
[
Voor 39% gewijzigd door
ThePrutser op 27-05-2010 15:42
. Reden: omdat ik altijd de helft vergeet! ]