Toon posts:

Freesco draait, maar zonder internet

Pagina: 1
Acties:

Verwijderd

Topicstarter
Ik heb een Freesco server geïnstalleerd, maar ik heb er twee problemen mee.
1) het interne netwerk draait, ik kan de netwerkkaarten pingen, maar de ip-adressen erachter niet. (dus ik log in met comp a, maar het ip van comp a is niet te pingen)

2) Ik krijg geen internetverbinding, tenminste, als ik met ifconfig kijk zie ik dat er wel contact is geweest tussen eth0 en iig de kabelmodem. De maccode van eth0 heb ik gespoofd (ifconfig $INTNAME0 hw ether 00:01:02:10:AC:AE in rc_init). Oh ja, ik probeer de DNS-server vanuit de router zelf te pingen (wat dus niet lukt), niet vanuit een andere computer via het netwerk.

Wie kan me helpen. Hieronder recent log, errormelding en system.cfg. (let niet op de datum en tijd)

(Zie dat jullie vaak om reports en logs vragen, vandaar deze ontzettend lange lijst info)


recent log
Nov 10 12:17:32 - syslogd 1.3-3: restart (remote reception).
Nov 10 12:17:33 - kernel: Kernel logging (proc) started.
Nov 10 12:17:33 - kernel: Memory: sized by int13 088h
Nov 10 12:17:33 - kernel: Console: 16 point font, 480 scans
Nov 10 12:17:33 - kernel: Console: colour VGA+ 80x30, 1 virtual console (max 63)
Nov 10 12:17:33 - kernel: pci_init: no BIOS32 detected
Nov 10 12:17:33 - kernel: Calibrating delay loop.. ok - 4.71 BogoMIPS
Nov 10 12:17:33 - kernel: Memory: 14104k/16384k available (696k kernel code, 384k reserved, 512k data)
Nov 10 12:17:33 - kernel: This processor honours the WP bit even when in supervisor mode. Good.
Nov 10 12:17:33 - kernel: Swansea University Computer Society NET3.035 for Linux 2.0
Nov 10 12:17:33 - kernel: NET3: Unix domain sockets 0.13 for Linux NET3.035.
Nov 10 12:17:33 - kernel: Swansea University Computer Society TCP/IP for NET3.034
Nov 10 12:17:33 - kernel: IP Protocols: IGMP, ICMP, UDP, TCP
Nov 10 12:17:33 - kernel: Linux IP multicast router 0.07.
Nov 10 12:17:33 - kernel: Checking 'hlt' instruction... disabled
Nov 10 12:17:33 - kernel: Linux version 2.0.38 (root@localhost.localdomain) (gcc version 2.7.2.3) #4 Wed May 17 22:55:01 EDT 2000
Nov 10 12:17:33 - kernel: Starting kswapd v 1.4.2.2
Nov 10 12:17:33 - kernel: Serial driver version 4.13p1 with no serial options enabled
Nov 10 12:17:33 - kernel: ttyS00 at 0x03f8 (irq = 4) is a 16450
Nov 10 12:17:33 - kernel: ttyS01 at 0x02f8 (irq = 3) is a 16450
Nov 10 12:17:33 - kernel: lp1 at 0x0378, (polling)
Nov 10 12:17:33 - kernel: Real Time Clock Driver v1.09
Nov 10 12:17:33 - kernel: Ramdisk driver initialized : 16 ramdisks of 4096K size
Nov 10 12:17:33 - kernel: loop: registered device at major 7
Nov 10 12:17:33 - kernel: hda: WDC AC2420H, 405MB w/128kB Cache, CHS=989/15/56
Nov 10 12:17:33 - kernel: hdb: IBM-DALA-3540, 516MB w/96kB Cache, CHS=1049/16/63
Nov 10 12:17:33 - kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Nov 10 12:17:33 - kernel: Floppy drive(s): fd0 is 1.44M
Nov 10 12:17:33 - kernel: FDC 0 is an 8272A
Nov 10 12:17:33 - kernel: Ethernet Bridge 002 for NET3.035 (Linux 2.0)
Nov 10 12:17:33 - kernel: PPP: version 2.3.10 (demand dialling)
Nov 10 12:17:33 - kernel: TCP compression code copyright 1989 Regents of the University of California
Nov 10 12:17:33 - kernel: PPP line discipline registered.
Nov 10 12:17:33 - kernel: SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
Nov 10 12:17:33 - kernel: CSLIP: code copyright 1989 Regents of the University of California.
Nov 10 12:17:33 - kernel: Partition check:
Nov 10 12:17:33 - kernel: hda: hda1
Nov 10 12:17:33 - kernel: hdb: hdb1 < hdb5 >
Nov 10 12:17:33 - kernel: RAMDISK: Compressed image found at block 0
Nov 10 12:17:33 - kernel: EXT2-fs warning: checktime reached, running e2fsck is recommended
Nov 10 12:17:33 - kernel: VFS: Mounted root (ext2 filesystem).
Nov 10 12:17:34 - kernel: UMSDOS Beta 0.6 (compatibility level 0.4, fast msdos)
Nov 10 12:17:39 - syslogd 1.3-3: restart (remote reception).
Nov 10 12:17:44 - kernel: Adding Swap: 32764k swap-space (priority -1)
Nov 10 12:17:49 - kernel: ip_masq_icq: using TCP port range 60200-61000
Nov 10 12:17:49 - kernel: ip_masq_icq: loaded support on port 4000/UDP
Nov 10 12:17:51 - insmod: Cannot open /mnt/router/drv/*.o
Nov 10 12:17:51 - insmod: Cannot open /mnt/router/drv/*.o
Nov 10 12:17:51 - insmod: Symbol 'io' not found
Nov 10 12:17:53 - last message repeated 7 times
Nov 10 12:17:54 - kernel: smc-ultra.c: No SMC Ultra card found (i/o = 0x320).
Nov 10 12:17:54 - insmod: Initialization of /tmp/net/smc-ultra.o.A0 failed
Nov 10 12:17:54 - kernel: smc-ultra.c: No SMC Ultra card found (i/o = 0x320).
Nov 10 12:17:54 - insmod: Initialization of /tmp/net/smc-ultra.o.B0 failed
Nov 10 12:17:54 - insmod: Symbol 'io' not found
Nov 10 12:17:55 - insmod: Symbol 'io' not found
Nov 10 12:17:55 - kernel: ne.c: No NE*000 card found at i/o = 0x320
Nov 10 12:17:55 - insmod: Initialization of /tmp/prm/ne.o.A0 failed
Nov 10 12:17:55 - kernel: ne.c: No NE*000 card found at i/o = 0x320
Nov 10 12:17:55 - insmod: Initialization of /tmp/prm/ne.o.B0 failed
Nov 10 12:17:56 - insmod: Cannot open /mnt/router/drv/*.o
Nov 10 12:17:56 - insmod: Cannot open /mnt/router/drv/*.o
Nov 10 12:17:56 - insmod: Symbol 'io' not found
Nov 10 12:17:58 - last message repeated 7 times
Nov 10 12:17:58 - kernel: smc-ultra.c: No SMC Ultra card found (i/o = 0x340).
Nov 10 12:17:58 - insmod: Initialization of /tmp/net/smc-ultra.o.A1 failed
Nov 10 12:17:59 - kernel: smc-ultra.c: No SMC Ultra card found (i/o = 0x340).
Nov 10 12:17:59 - insmod: Initialization of /tmp/net/smc-ultra.o.B1 failed
Nov 10 12:17:59 - insmod: Symbol 'io' not found
Nov 10 12:17:59 - insmod: Symbol 'io' not found
Nov 10 12:18:00 - kernel: ne.c: No NE*000 card found at i/o = 0x340
Nov 10 12:18:00 - insmod: Initialization of /tmp/prm/ne.o.A1 failed
Nov 10 12:18:00 - kernel: ne.c: No NE*000 card found at i/o = 0x340
Nov 10 12:18:00 - insmod: Initialization of /tmp/prm/ne.o.B1 failed
Nov 10 12:18:00 - insmod: Cannot open /mnt/router/drv/*.o
Nov 10 12:18:00 - insmod: Cannot open /mnt/router/drv/*.o
Nov 10 12:18:01 - insmod: Symbol 'io' not found
Nov 10 12:18:03 - last message repeated 7 times
Nov 10 12:18:03 - kernel: smc-ultra.c: No SMC Ultra card found (i/o = 0x330).
Nov 10 12:18:03 - insmod: Initialization of /tmp/net/smc-ultra.o.A2 failed
Nov 10 12:18:03 - kernel: smc-ultra.c: No SMC Ultra card found (i/o = 0x330).
Nov 10 12:18:03 - insmod: Initialization of /tmp/net/smc-ultra.o.B2 failed
Nov 10 12:18:04 - insmod: Symbol 'io' not found
Nov 10 12:18:04 - insmod: Symbol 'io' not found
Nov 10 12:18:04 - kernel: ne.c: No NE*000 card found at i/o = 0x330
Nov 10 12:18:04 - insmod: Initialization of /tmp/prm/ne.o.A2 failed
Nov 10 12:18:05 - kernel: ne.c: No NE*000 card found at i/o = 0x330
Nov 10 12:18:05 - insmod: Initialization of /tmp/prm/ne.o.B2 failed
Nov 10 12:18:05 - insmod: Cannot open /mnt/router/drv/*.o
Nov 10 12:18:05 - kernel: eth0: 3c509 at 0x320 tag 1, 10baseT port, address 00 60 8c f2 65 d8, IRQ 5.
Nov 10 12:18:05 - kernel: 3c509.c:1.16 2/3/98 becker@cesdis.gsfc.nasa.gov
Nov 10 12:18:05 - kernel: eth1: 3c509 at 0x340 tag 2, 10baseT port, address 00 60 8c f2 65 eb, IRQ 7.
Nov 10 12:18:05 - kernel: 3c509.c:1.16 2/3/98 becker@cesdis.gsfc.nasa.gov
Nov 10 12:18:05 - kernel: eth2: 3c509 at 0x330 tag 3, 10baseT port, address 00 a0 24 b6 75 50, IRQ 3.
Nov 10 12:18:05 - kernel: 3c509.c:1.16 2/3/98 becker@cesdis.gsfc.nasa.gov
Nov 10 12:18:06 - kernel: 3c59x.c:v0.99H 11/17/98 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
Nov 10 12:18:06 - insmod: Initialization of /tmp/net/3c59x.o.C failed
Nov 10 12:18:06 - kernel: ne2k-pci.c:v0.99L 2/7/98 D. Becker/P. Gortmaker http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html
Nov 10 12:18:06 - insmod: Initialization of /tmp/net/ne2k-pci.o.C failed
Nov 10 12:18:06 - insmod: Initialization of /tmp/net/rtl8139.o.C failed
Nov 10 12:18:07 - kernel: smc-ultra.c: Presently autoprobing (not recommended) for a single card.
Nov 10 12:18:07 - kernel: smc-ultra.c: No SMC Ultra card found (i/o = 0x0).
Nov 10 12:18:07 - insmod: Initialization of /tmp/net/smc-ultra.o.C failed
Nov 10 12:18:07 - insmod: Initialization of /tmp/net/tulip.o.C failed
Nov 10 12:18:07 - kernel: ne.c: No PCI cards found. Use "io=0xNNN" value(s) for ISA cards.
Nov 10 12:18:07 - insmod: Initialization of /tmp/prm/ne.o.C failed
Nov 10 12:18:10 - mode: User 'init' issued 'mode ethernet'
Nov 10 12:18:11 - kernel: eth0: Setting Rx mode to 1 addresses.
Nov 10 12:18:12 - kernel: eth1: Setting Rx mode to 0 addresses.
Nov 10 12:18:12 - kernel: eth1: Setting Rx mode to 1 addresses.
Nov 10 12:18:13 - kernel: eth2: Setting Rx mode to 0 addresses.
Nov 10 12:18:13 - kernel: eth2: Setting Rx mode to 1 addresses.
Nov 10 12:18:15 - named[173]: starting. named 4.9.3-BETA26 Sun Nov 26 20:58:49 CST 1995 ^Iroot@fuzzy:/tmp/bind-4.9.3-BETA26/named
Nov 10 12:18:15 - named[173]: cache zone "" loaded (serial 0)
Nov 10 12:18:15 - named[173]: primary zone "inet" loaded (serial 1999317)
Nov 10 12:18:15 - named[173]: primary zone "10.in-addr.arpa" loaded (serial 1999317)
Nov 10 12:18:16 - named[173]: primary zone "16.172.in-addr.arpa" loaded (serial 1999317)
Nov 10 12:18:16 - named[173]: primary zone "168.192.in-addr.arpa" loaded (serial 1999317)
Nov 10 12:18:16 - named[173]: primary zone "0.0.127.in-addr.arpa" loaded (serial 1999317)
Nov 10 12:18:16 - named[174]: Ready to answer queries.
Nov 10 12:18:20 - dhcpd: DHCPREQUEST for 192.168.1.2 from 00:01:02:10:ac:ae via eth1
Nov 10 12:18:20 - dhcpd: DHCPACK on 192.168.1.2 to 00:01:02:10:ac:ae via eth1
Nov 10 12:18:37 localhost thttpd[361]: thttpd/2.05 09nov99 starting on port 82
Nov 10 12:18:37 localhost thttpd[361]: started as root without requesting chroot(), warning only
Nov 10 12:18:58 - login: ROOT LOGIN ON ttyp0 FROM 192.168.1.2
Nov 10 12:19:09 - kernel: IP fw-in rej eth0 ICMP/0 212.142.28.66 212.187.11.103 L=84 S=0x00 I=26321 F=0x0000 T=254
Nov 10 12:19:10 - kernel: IP fw-in rej eth0 ICMP/0 212.142.28.66 212.187.11.103 L=84 S=0x00 I=26927 F=0x0000 T=254
Nov 10 12:19:11 - kernel: IP fw-in rej eth0 ICMP/0 212.142.28.66 212.187.11.103 L=84 S=0x00 I=27569 F=0x0000 T=254
Nov 10 12:19:12 - kernel: IP fw-in rej eth0 ICMP/0 212.142.28.66 212.187.11.103 L=84 S=0x00 I=28120 F=0x0000 T=254
Nov 10 12:19:14 - kernel: IP fw-in rej eth0 ICMP/0 212.142.28.66 212.187.11.103 L=84 S=0x00 I=29459 F=0x0000 T=254
Nov 10 12:19:15 - kernel: IP fw-in rej eth0 ICMP/0 212.142.28.66 212.187.11.103 L=84 S=0x00 I=30128 F=0x0000 T=254



Errormelding
named[177]: ns_forw: sendto([212.142.28.66].53): Network is unreachable



system.cfg
----- cat /etc/system.cfg -----
# [System]
ROUTER=ethernet# 0.dialup/leased/ethernet/bridge
HOSTNAME=router#711.Router name
DOMAIN=inet#712.(Local) domain name
ENAMSQ=y # 11.Enable NAT and firewall
ENABRG=n # 12.Enable bridging mode? DONT TOUCH!!!
BIGMEM=n # 13.If 16+MB RAM start ppp bsd compression
SAVERS=0,12 # 14.Savers - screen(min),hdd(x5 sec) 0 -off
SWPSIZE=32# 15.Swap size in Kb on boot device. 0 - off
LOGSIZE=30000,3000# 16.System_log,logins_log sizes (bytes)
DEFISP=# 6.Default dialup ISP

# [Services] # y - worldwide/s - local/n - disable
ENADNS=s #411.Enable caching DNS server
LOGDNS=n#412.Enable debug info
ENADHCP=s #421.Enable DHCP server
WINSADDR=#422.WINS address (for DHCP server)
LIZTIME=86400,86400#423.default-lease-time,max-lease-time
ENAWWW=n #431.Enable Public HTTP Server
WWWPORT=80 #432.on port
ENAWWA=s #441.Enable Time Server and control via HTTP
WWAPORT=82 #442.on port
TIMADDR=#443.Host timeserver address, empty - disable
TIMZONE=+0400#444.Offset to UTC (-1200 -:- +1200)
ENALPD=n #451.Enable Print Server
LPPORT1=515#452.on port
LPDEV1=lp1#453.on output device
LPPORT2=516#454.Second lp server on port, empty - disable
LPDEV2=lp2#455.on output device
ENATEL=s# 46.Enable telnet server


# [Security]
TRUSTLN=p #211.Trust local nets y/n/p{artual}
TRUSTMD=y#212.Modem links have access to local networks
RINGS=2,7#220.Rings before answer at login,nologin time
MonTIM=""#221.Nologin times for modem users
TueTIM=""#222
WedTIM=""#223
ThuTIM=""#224
FriTIM=""#225
SatTIM=""#226
SunTIM=""#227


# [Modems]
MODEM0= # 51.1st modem
MSPEED0=# 52.port's speed
MINIT0=""# 53.init string
MTU0=#541.Maximum Transmit Unit
MRU0=#542.Maximum Receive Unit
MADDR0=212.187.11.103# 55.ppp link remote addr (for dialin purpose)

MODEM1= # 61
MSPEED1=# 62
MINIT1=""# 63
MTU1=#641
MRU1=#642
MADDR1=192.168.168.3# 65.I said for dialin purpose.


# [leased line router]
ADRTYPE= #921.if ISP supplies us with dynamic IP, then:
LOCAL=127.0.0.2 #922.fake local side ppp IP addr
REMOTE=127.0.0.3 #923.fake remote addr


# [ethernet/leased/printer/ras router]
GATEWAY=212.187.8.1#911.Default gateway, if exist.
DNSADDR=212.142.28.66#912.Primary DNS address for ethernet connection
DNSADDR1=212.142.28.130#913.Secondary DNS address for ethernet connection
PROXY=""#914.HTTP proxy addr[:port]


# [Hardware]
IO0=0x320#811.1st ethernet card I/O address
IRQ0=5#812.IRQ line
IO1=0x340#821
IRQ1=7#822
IO2=0x330#831
IRQ2=3#832


# [Networks]
USEDHCP0=n#720.Use DHCP client to config this interface
INTNAME0=eth0#721.Interface name (eth0|arc0e|arc0)
DHCPLOG=n#722.Enable DHCP client messages in the log
DHCPDNS=y#723 Enable auto configuration of DNS via DHCP
IPADDR0=212.187.11.103#724.IP adress of this interface
NETMASK0=255.255.255.0 #725.Network mask
NETWORK0=212.187.11.0# Network address
BRDCAST0=212.187.11.255# Broadcast address
#726.IP pool, empty disables DHCP on this interface
IPRANGE0=""

INTNAME1=eth1#731.Interface name (eth1|eth0:1|arc0e|arc0 etc)
IPADDR1=192.168.1.1#732. Second network
NETMASK1=255.255.255.0
NETWORK1=192.168.1.0
BRDCAST1=192.168.1.255
IPRANGE1="192.168.1.2 192.168.1.2"

INTNAME2=eth2#74x. Third network
IPADDR2=192.168.0.1
NETMASK2=255.255.255.0
NETWORK2=192.168.0.0
BRDCAST2=192.168.0.255
IPRANGE2="192.168.0.2 192.168.0.2"



----- cat /etc/live.cfg -----
VER=0.2.7
bootdev=hda1
UPTIME="Sat Nov 10 11:58:13 2001"
DONE="echo Done"


----- cat /etc/dhcpc/dhcpcd-eth0.info -----


----- cat /etc/forward.cfg -----
_t,1025,192.168.1.1/1025

#_47x._[Port_forwarding_AKA_export_services]
#_
#_tcp|udp,incoming_port,local_computer_IP_addr/port
#_
#_Example:_t,80,192.168.168.2/80
#_this_will_open_worldwide_web_server_on_local_computer_192.168.168.2
#_
#_Example:_t,21,192.168.168.3/21
#_this_will_open_worldwide_ftp_server_on_local_computer_192.168.168.2
#_
#_Comment_must_be_on_separate_line_start_with_"#_"_and_should_not_have_spaces



----- cat /etc/banlist.cfg -----
#_23._[List_of_banned_hosts/nets_one_record_per_line]
#_
#_local|external,IP_addr[/netmask_or_netbits_if_baning_a_whole_net]
#_
#_Example:_l,123.124.125.0/24_ban_local_net
#_Example:_e,123.124.125.0/255.255.255.0_ban_external_net
#_Example:_l,10.0.0.123_ban_local_host
#_
#_Comment_must_be_on_separat_lines_start_with_"#_"_and_should_not_have_spaces



----- sed -n 1,/AUTH/P /etc/chat.pwd -----


----- lsmod -----
ModulePagesUsed by
/tmp/net/3c509.o.C 23
ip_masq_ftp 10
ip_masq_irc 10
ip_masq_quake 10
ip_masq_vdolive 10
ip_masq_raudio 10
ip_masq_icq 10
ip_masq_cuseeme 10
8390 20


----- dmesg | grep eth -----
eth0: 3c509 at 0x320 tag 1, 10baseT port, address 00 60 8c f2 65 d8, IRQ 5.
eth1: 3c509 at 0x340 tag 2, 10baseT port, address 00 60 8c f2 65 eb, IRQ 7.
eth2: 3c509 at 0x330 tag 3, 10baseT port, address 00 a0 24 b6 75 50, IRQ 3.
eth0: Setting Rx mode to 1 addresses.
eth1: Setting Rx mode to 0 addresses.
eth1: Setting Rx mode to 1 addresses.
eth2: Setting Rx mode to 0 addresses.
eth2: Setting Rx mode to 1 addresses.


----- ifconfig -----
lo Link encap:Local Loopback
inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0
UP BROADCAST LOOPBACK RUNNING MTU:3584 Metric:1
RX packets:1174 errors:0 dropped:0 overruns:0
TX packets:1174 errors:0 dropped:0 overruns:0

eth0 Link encap:10Mbps Ethernet HWaddr 00:01:02:10:AC:AE
inet addr:212.187.11.103 Bcast:212.187.11.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:634 errors:0 dropped:0 overruns:0
TX packets:0 errors:0 dropped:0 overruns:0
Interrupt:5 Base address:0x320

eth1 Link encap:10Mbps Ethernet HWaddr 00:60:8C:F2:65:EB
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:240 errors:0 dropped:0 overruns:0
TX packets:192 errors:0 dropped:0 overruns:0
Interrupt:7 Base address:0x340

eth2 Link encap:10Mbps Ethernet HWaddr 00:A0:24:B6:75:50
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
TX packets:0 errors:0 dropped:0 overruns:0
Interrupt:3 Base address:0x330



----- cat /proc/interrupts -----
0: 52751 timer
1: 8 keyboard
2: 0 cascade
3: 0 3c509
5: 634 3c509
7: 262 3c509
8: 1 + rtc
13: 0 math error
14: 2061 + ide0


----- cat /proc/ioports -----
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-009f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : npu
01f0-01f7 : ide0
02f8-02ff : serial(auto)
0320-032f : 3c509
0330-033f : 3c509
0340-034f : 3c509
0378-037f : lp
03c0-03df : vga+
03f0-03f5 : floppy
03f6-03f6 : ide0
03f7-03f7 : floppy DIR
03f8-03ff : serial(auto)


----- route -n -----
Kernel routing table
Destination Gateway Genmask Flags MSS Window Use Iface
255.255.255.255 * 255.255.255.255 UH 1500 0 0 eth2
255.255.255.255 * 255.255.255.255 UH 1500 0 1 eth1
255.255.255.255 * 255.255.255.255 UH 1500 0 0 eth0
212.187.11.0 * 255.255.255.0 U 1500 0 0 eth0
192.168.1.0 * 255.255.255.0 U 1500 0 1 eth1
192.168.0.0 * 255.255.255.0 U 1500 0 0 eth2
127.0.0.0 * 255.0.0.0 U 3584 0 2 lo


----- cat /etc/dhcpd.leases -----
lease 192.168.0.2 {
starts 6 2001/11/10 09:48:08;
ends 0 2001/11/11 09:48:08;
hardware ethernet 00:01:02:10:ac:ae;
uid 01:00:01:02:10:ac:ae;
client-hostname "Q0S9D9";
}
lease 192.168.1.2 {
starts 6 2001/11/10 11:49:11;
ends 0 2001/11/11 11:49:11;
hardware ethernet 00:01:02:10:ac:ae;
uid 01:00:01:02:10:ac:ae;
client-hostname "Q0S9D9";
}
lease 192.168.1.2 {
starts 6 2001/11/10 11:58:33;
ends 0 2001/11/11 11:58:33;
hardware ethernet 00:01:02:10:ac:ae;
uid 01:00:01:02:10:ac:ae;
client-hostname "Q0S9D9";
}


----- free -----
total: used: free: shared: buffers: cached:
Mem: 15147008 10579968 4567040 6000640 3805184 1126400
Swap: 33550336 0 33550336
MemTotal: 14792 kB
MemFree: 4460 kB
MemShared: 5860 kB
Buffers: 3716 kB
Cached: 1100 kB
SwapTotal: 32764 kB
SwapFree: 32764 kB

Mounted FS:
/dev/root / ext2 rw 0 0
/proc /proc proc rw 0 0
/dev/hda1 /mnt umsdos rw 0 0

Filesystem 1024-blocks Used Available Capacity Mounted on
/dev/ram0 2548 2135 413 84% /
/dev/hda1 414712 35696 379016 9% /mnt


----- ps -----
PidStat ParentNameCommand
1 S0initinit
2 S1kflushd
3 S1kswapd
4 S1logrotatesh/bin/logrotate
6 S1syslogdsyslogd-r-h-m0
8 S1klogdklogd
19 S1daemonsh/bin/daemon-agetty 9600 tty2
24 S19agettyagetty9600tty2
177 S1namednamed
206 S1dhcpddhcpd-qeth1eth2
364 S1thttpdthttpd-p82-uroot-d/wwa-l/dev/null
367 S1daemonsh/bin/daemon-telnetd -debug
369 S367telnetdtelnetd-debug
393 S1daemonsh/bin/daemon-agetty 9600 tty1
395 S393agettyagetty9600tty1
515 S1adm.cgishadm.cgishell
516 S1sedseds/</\<\;/g;s/>/\>\;/g
517 S515pingping134.224.210.104
572 S1adm.cgishadm.cgishell
573 S1sedseds/</\<\;/g;s/>/\>\;/g
574 S572pingping212.187.11.103
617 S1adm.cgishadm.cgishell
618 S1sedseds/</\<\;/g;s/>/\>\;/g
619 S617pingping212.187.11.103
776 S364usr.cgishusr.cgiinfo
777 S776sysinfosh/bin/sysinfo
778 S776sedseds/</\<\;/g;s/>/\>\;/g
812 S4sleepsleep10
813 R777pssh/bin/ps


----- cat /etc/ppp/opt* -----
asyncmap 0


----- setserial -bg /dev/cua? -----
/dev/cua0 at 0x03f8 (irq = 4) is a 16450
/dev/cua1 at 0x02f8 (irq = 3) is a 16450

  • flat
  • Registratie: Mei 2000
  • Niet online
ehm sorry heb geen tijd om alles te lezen, maar kan je vanaf je server wel pingen naar bijvoorbeeld www.google.com?

want dan weet je waar 't aan ligt

"Happiness is a way of travel, not a destination."
--Roy Goodman


Verwijderd

Topicstarter
Nee, ik heb dus GEEN internetverbinding. Kan de DNS server niet pingen, laat staan www.google.com. Er is wel twee-weg contact (geweest) tussen eth0 en het kabelmomdem.

Mac-code is gespoofd dus die kan het ook niet zijn.

En NICŽs wisselen van comp kan niet. wan alle NIC (behalve de originele zijn ISA-NIC en alleen de ouwe 486 die als router dient kan ISA-NICŽs aan.

  • flat
  • Registratie: Mei 2000
  • Niet online
hmmz tja dan weet ik 't ook niet meer

"Happiness is a way of travel, not a destination."
--Roy Goodman


Verwijderd

Heb je alle I/O's en IRQ wel goed staan voor je netwerk kaarten??? dit probleem had ik ook, besloten om op mijn 486 toch maar 2 pci'tjes te poten en toen was het gaan.

maar krijg je wel een dhcp offer op je nic van je provider?