resetten van een HP 1920-8G-PoE switch

[107mb]

ik heb een HP Switch 1920-8G-PoE (JG921A) gekregen. Deze moet ik echter wel resetten en naar de fabrieksinstellingen terug krijgen. Ik heb er geen console-kabel bij gekregen (RJ45 en com aansluiting).
De switch heeft ook geen reset button die je bv met een paperclip kunt indrukken

Via internet heb ik vernomen dat als je minstens 45 seconden een standaard ethernet kabel op poort 1 en 2 aansluit, de switch naar fabrieksinstellingen teruggaat. Het default IP adres wordt dan 192.168.1.1.

Nadat ik deze stap heb uitgevoerd, koppel ik mijn laptop aan de switch, en pas handmatig mijn IP adres aan in 192.168.1.100 / 255.255.255.0. Gateway heb ik leeggelaten. Ook heb ik de wifi adapter uitgeschakeld.

Als ik dan met Angry IP ga scannen, kom ik geen enkel IP adres tegen.

Weet iemand wat ik fout doe?

[ijske]

ik heb mijne met de console kabel gedaan, omdat ik het niet voor elkaar kreeg via die manier inderdaad..

[Out.of.Control]

Die truc met een kabel tussen poort 1 en 2 werkt ook op een 1700 switch, maar als ik me goed herinner moet je dan wel opstarten met de kabel in die poorten (dus switch uit, kabel erin, switch aan en wachten maar).
Heb je dat wellicht al geprobeerd?

[_Hades_]

Die truuk van poort 1 en 2 werkt alleen op de 1800 series switch (en 1700 blijkbaar ☝️). Als je geluk hebt staat ie op dhcp en kun je er via die weg in komen. Anders is de switch die jij hebt is alleen met console kabel te resetten (vrij simpel hoor, je moet alleen net ff de kabel ervoor hebben (is ook een standaard seriele kabel)).

[TommieW]

Volgens de specs staat hij default in DHCP modus. Prik 'm eens in je netwerk en kijk in je DHCP server of hij een lease krijgt.

Edit: de documentatie heeft het over een reset knopje: https://support.hpe.com/h...cId=emr_na-a00023093en_us

[ Voor 24% gewijzigd door TommieW op 23-12-2020 20:19 ]

[107mb]

ik kan geen fysiek reset knopje vinden....
ik heb nu een 580 pagina manual voor mijn neus, die ga ik maar eens even doorspitten :-)

[Ben(V)]

De reset switch zit linksonder op het front paneel.
Staat ook reset bij.
Paperclip of zoiets nodig om ze in te drukken.
Na een reset doet hij dhcp.

[ Voor 65% gewijzigd door Ben(V) op 23-12-2020 23:34 ]

[Xander]

Ben(V) schreef op woensdag 23 december 2020 @ 23:29:
De reset switch zit linksonder op het front paneel.
Staat ook reset bij.
Paperclip of zoiets nodig om ze in te drukken.
Na een reset doet hij dhcp.

[Afbeelding]

Dat is een ander model switch.

[_Hades_]

Ben(V) schreef op woensdag 23 december 2020 @ 23:29:
De reset switch zit linksonder op het front paneel.
Staat ook reset bij.

Dat is niet de switch die hij heeft. Ander typenummer. De 1920 die TS heeft is een comware model (oud 3com/h3c). De switch die jij quote is een 1920s, zelfde productlijn maar een compleet andere switch/software.

[kosz]

Console kabel is wel het makkelijkste, maar die heb je niet...
Je kan wel via wireshark op de poorten van de switch kijken welke arp berichten deze uitstuurt om achter het ip-adres van de switch te komen.
Gebruik wel een capture filter om je eigen zooi van je pc uit je capture te houden :
not ether host 00:00:00:00:00:00 and arp (met je eigen mac-adres uiteraard)

[107mb]

Xander schreef op woensdag 23 december 2020 @ 23:38:
[...]

Dat is een ander model switch.

[Afbeelding]

ik heb idd deze switch. ik probeer een console kabel te versieren... bestaan deze ook naar USB? Want ik heb natuurlijk geen laptop/PC met een rs232 poort.

ik ga ook de tips van @kosz uitvoeren.

is er iemand in de buurt van Hengelo die een consolekabel te leen heeft? ik heb nog een oude PC gevonden met een com poort.

[ Voor 9% gewijzigd door 107mb op 24-12-2020 10:15 ]

[kosz]

Ja er zijn USB to rs323 converteren naar dan moet je nog steeds een console kabel hebben.
Als het paswoord niet meer default is zal je de switch tijdens het booten moeten onderbreken :
https://community.hpe.com...0-48G-JG927A/td-p/6853127

[dasiro]

ff threaddiggen om toch een oplossing te geven voor als er een console-wachtwoord in staat.

verbind via console op 38400b en boot de switch, je zal in
ctrl+B hetEXTEND-BOOTWARE MENU komen. De optie "Restore to Factory Default Configuration" zal niet werken en "Clear Super Password" helpt niet. Je moet "Skip Current System Configuration" kiezen en dan "Boot System" om dan het commando "initialize" te geven

dit is een dump van wat ik in de console gedaan heb, er staat wat teveel info in, dus gewoon de stappen van hierboven volgen (serienummer en mac-adressen die mogelijk zichtbaar maakt me niet zoveel uit, want het is een oude switch om mee te spelen):

code:

System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU

======================<BASIC-BOOTWARE MENU(Ver 1.22)>=======================
|<1> Modify Serial Interface Parameter                                     |
|<2> Update Extend BootWare                                                |
|<3> Update Full BootWare                                                  |
|<4> Boot Extend BootWare                                                  |
|<5> Boot Backup Extend BootWare                                           |
|<0> Reboot                                                                |
============================================================================
Enter your choice(0-5): 2
Please Start To Transfer File, Press <Ctrl+C> To Exit.
Waiting ...CC
stopped!
Download failed!

======================<BASIC-BOOTWARE MENU(Ver 1.22)>=======================
|<1> Modify Serial Interface Parameter                                     |
|<2> Update Extend BootWare                                                |
|<3> Update Full BootWare                                                  |
|<4> Boot Extend BootWare                                                  |
|<5> Boot Backup Extend BootWare                                           |
|<0> Reboot                                                                |
============================================================================
Enter your choice(0-5): 0
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing..........................Done!

****************************************************************************
*                                                                          *
*            HPE 1920-8G Switch JG920A BootWare, Version 1.22              *
*                                                                          *
****************************************************************************
Copyright (c) 2010-2017 Hewlett Packard Enterprise Development LP

Compiled Date       : Apr 14 2017 15:05:19
CPU Type            : MIPS4kec
CPU L1 Cache        : 16KB
CPU Clock Speed     : 500MHz
Memory Type         : DDR3 SDRAM
Memory Size         : 128MB
Memory Speed        : 300MHz
BootWare Size       : 3MB
Flash Size          : 32MB


BootWare Validating...
Press Ctrl+B to enter extended boot menu...
BootWare password: Not required. Please press Enter to continue.

Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 5
Password recovery capability is enabled. To perform this operation, first
disable the password recovery capability using the undo password-recovery
enable command in CLI.

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 8
Clear Application Password Success!

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 0
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing..........................Done!

****************************************************************************
*                                                                          *
*            HPE 1920-8G Switch JG920A BootWare, Version 1.22              *
*                                                                          *
****************************************************************************
Copyright (c) 2010-2017 Hewlett Packard Enterprise Development LP

Compiled Date       : Apr 14 2017 15:05:19
CPU Type            : MIPS4kec
CPU L1 Cache        : 16KB
CPU Clock Speed     : 500MHz
Memory Type         : DDR3 SDRAM
Memory Size         : 128MB
Memory Speed        : 300MHz
BootWare Size       : 3MB
Flash Size          : 32MB


BootWare Validating...
Press Ctrl+B to enter extended boot menu...
Starting to get the main application file--flash:/jg920a-cmw520-r1120.bin!..
............................................................................
.................
The main application file is self-decompressing.............................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
......Done!
System application is starting...
User interface aux0 is available.



Press ENTER to get started.

Login authentication


Username:admin
Password:
% Login failed!

Username:admin
Password:
% Login failed!

Username:
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing..........................Done!

****************************************************************************
*                                                                          *
*            HPE 1920-8G Switch JG920A BootWare, Version 1.22              *
*                                                                          *
****************************************************************************
Copyright (c) 2010-2017 Hewlett Packard Enterprise Development LP

Compiled Date       : Apr 14 2017 15:05:19
CPU Type            : MIPS4kec
CPU L1 Cache        : 16KB
CPU Clock Speed     : 500MHz
Memory Type         : DDR3 SDRAM
Memory Size         : 128MB
Memory Speed        : 300MHz
BootWare Size       : 3MB
Flash Size          : 32MB


BootWare Validating...
Press Ctrl+B to enter extended boot menu...
BootWare password: Not required. Please press Enter to continue.

Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9):

Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. All rights reserved.

This document provides copyright information regarding the third-party software
that are included, either in whole or in part, in this product.

This product contains third parties component softwares and they will be used
and distributed under the specific license. This product contains some
components under the GNU General Public License ("GPL") version 2.0, the GNU
Lesser General Public License("LGPL") version 2.1 or other open source
licenses. H3C agrees to provide the open source code which is under GPL for
three (3) years from the first release date of the software. If you want to
obtain a copy of GPL licensed source code associated with this product, please
send a request to [e-mail] or write to New H3C Technologies Co., Ltd.
466 Changhe Road, Binjiang District, Hangzhou, Zhejiang Province 310052,
P.R. China.The product name and version number of the software, your name,
phone number and address should be included in the request. H3C reserves
the right to charge an amount of cost for distribution of source code ,
consistent with the GPL license terms. You can also obtain a copy of the GPL
Please enter q/Q to quit,other key continue....
and LGPL at http://www.gnu.org/licenses/.

--------------------------------------------------------------------------------

The following software may be included in this product:
  U-BOOT 1.1.4

Use of any of this software is governed by the terms of the license below:


# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
# GNU General Public License for more details.
#
Please enter q/Q to quit,other key continue....
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA


                    GNU GENERAL PUBLIC LICENSE
                       Version 2, June 1991

 Copyright (C) 1989, 1991 Free Software Foundation, Inc.
 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 Everyone is permitted to copy and distribute verbatim copies
 of this license document, but changing it is not allowed.

                            Preamble

  The licenses for most software are designed to take away your
freedom to share and change it.  By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change free
software--to make sure the software is free for all its users.  This
Please enter q/Q to quit,other key continue....
General Public License applies to most of the Free Software
Foundation's software and to any other program whose authors commit to
using it.  (Some other Free Software Foundation software is covered by
the GNU Library General Public License instead.)  You can apply it to
your programs, too.

  When we speak of free software, we are referring to freedom, not
price.  Our General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and charge for
this service if you wish), that you receive source code or can get it
if you want it, that you can change the software or use pieces of it
in new free programs; and that you know you can do these things.

  To protect your rights, we need to make restrictions that forbid
anyone to deny you these rights or to ask you to surrender the rights.
These restrictions translate to certain responsibilities for you if you
distribute copies of the software, or if you modify it.

  For example, if you distribute copies of such a program, whether
gratis or for a fee, you must give the recipients all the rights that
Please enter q/Q to quit,other key continue....
you have.  You must make sure that they, too, receive or can get the
source code.  And you must show them these terms so they know their
rights.

  We protect your rights with two steps: (1) copyright the software, and
(2) offer you this license which gives you legal permission to copy,
distribute and/or modify the software.

  Also, for each author's protection and ours, we want to make certain
that everyone understands that there is no warranty for this free
software.  If the software is modified by someone else and passed on, we
want its recipients to know that what they have is not the original, so
that any problems introduced by others will not reflect on the original
authors' reputations.

  Finally, any free program is threatened constantly by software
patents.  We wish to avoid the danger that redistributors of a free
program will individually obtain patent licenses, in effect making the
program proprietary.  To prevent this, we have made it clear that any
patent must be licensed for everyone's free use or not licensed at all.
Please enter q/Q to quit,other key continue....

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 2

===========================<Enter Serial SubMenu>===========================
|Note:the operating device is flash                                        |
|<1> Download Application Program To SDRAM And Run                         |
|<2> Update Main Application File                                          |
|<3> Update Backup Application File                                        |
|<4> Update Secure Application File                                        |
|<5> Modify Serial Interface Parameter                                     |
|<0> Exit To Main Menu                                                     |
============================================================================
Enter your choice(0-5): 5

===============================<BAUDRATE SET>===============================
|Note:'*'indicates the current baudrate                                    |
|     Change The HyperTerminal's Baudrate Accordingly                      |
|---------------------------<Baudrate Available>---------------------------|
|<1> 9600(Default)                                                         |
|<2> 19200                                                                 |
|<3> 38400*                                                                |
|<4> 57600                                                                 |
|<5> 115200                                                                |
|<0> Exit                                                                  |
============================================================================
Enter your choice(0-5): 0

===========================<Enter Serial SubMenu>===========================
|Note:the operating device is flash                                        |
|<1> Download Application Program To SDRAM And Run                         |
|<2> Update Main Application File                                          |
|<3> Update Backup Application File                                        |
|<4> Update Secure Application File                                        |
|<5> Modify Serial Interface Parameter                                     |
|<0> Exit To Main Menu                                                     |
============================================================================
Enter your choice(0-5): 0

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 5
Password recovery capability is enabled. To perform this operation, first
disable the password recovery capability using the undo password-recovery
enable command in CLI.

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 8
Clear Application Password Success!

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 5
Password recovery capability is enabled. To perform this operation, first
disable the password recovery capability using the undo password-recovery
enable command in CLI.

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 6
Flag Set Success.

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 1
Starting to get the main application file--flash:/jg920a-cmw520-r1120.bin!..
............................................................................
.................
The main application file is self-decompressing.............................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
......Done!
System application is starting...
Configuration file is skipped.
User interface aux0 is available.



Press ENTER to get started.
<HPE>
#Apr 26 12:00:17:069 2000 HPE SHELL/4/LOGIN:
 Trap 1.3.6.1.4.1.25506.2.2.1.1.3.0.1: login from Console
%Apr 26 12:00:17:199 2000 HPE SHELL/5/SHELL_LOGIN: Console logged in from aux0.
<HPE>initialize
 The startup configuration file will be deleted and the system will be rebooted. Continue? [Y/N]:y
 Please wait.......
#Apr 26 12:01:25:025 2000 HPE DEVM/1/REBOOT:
 Reboot device by command.

%Apr 26 12:01:25:109 2000 HPE DEVM/5/SYSTEM_REBOOT: System is rebooting now.
 Now rebooting, please wait...
<HPE>
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing..........................Done!

****************************************************************************
*                                                                          *
*            HPE 1920-8G Switch JG920A BootWare, Version 1.22              *
*                                                                          *
****************************************************************************
Copyright (c) 2010-2017 Hewlett Packard Enterprise Development LP

Compiled Date       : Apr 14 2017 15:05:19
CPU Type            : MIPS4kec
CPU L1 Cache        : 16KB
CPU Clock Speed     : 500MHz
Memory Type         : DDR3 SDRAM
Memory Size         : 128MB
Memory Speed        : 300MHz
BootWare Size       : 3MB
Flash Size          : 32MB


BootWare Validating...
Press Ctrl+B to enter extended boot menu...
Starting to get the main application file--flash:/jg920a-cmw520-r1120.bin!..
............................................................................
.................
The main application file is self-decompressing.............................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
......Done!
System application is starting...
Startup configuration file does not exist.
It will take a long time to get configuration file, please wait...
Press CTRL_C to break

Retrieving configuration file failed!

Configuring default settings.
User interface aux0 is available.



Press ENTER to get started.

Login authentication


Username:admin
Password:
<HPE>
#Apr 26 12:00:41:659 2000 HPE SHELL/4/LOGIN:
 Trap 1.3.6.1.4.1.25506.2.2.1.1.3.0.1:admin login from Console
%Apr 26 12:00:41:789 2000 HPE SHELL/5/SHELL_LOGIN: admin logged in from aux0.
<HPE>