Hallo,
Ik zit met deze subwoefer:
http://www.ecoustics.com/...um/home-audio/646685.html
Hij heeft drie aansluitingen elke voor een ("spreek"?) spoel van 8 ohm (voice-coil in het english).
Ik wil proberen deze aan te sluiten op een amplifier. De subwoefer heeft een specificatie van 210 RMS en werd waarschijnlijk aangedreven door 3 BASH amplifiers die 70 watts leverden (?).
De vraag is nu ten eerste hoe deze subwoefer aan te sluiten zodat de ohms een beetje kloppen ?
Ik heb zelf een serieel tekeningetje en een parallel tekeningetje gemaakt voor zover ik dit begrijp.
Tevens een "special wiring" tekeningtje gemaakt aan de hand van deze beschrijving:
http://forums.creative.com/archive/index.php?t-489341.html
De persoon in kwestie heeft het over een "2 ohms" configuratie geschikt voor een 8 ohms amplifier ? (HUH?)
En dat is gemeten met een digital multi meter, kan zijn dat mijn tekeningtje niet klopt:
Hier is mijn tekeningetje:
http://www.skybuck.org/Gi...rippleVoiceCoilWiring.jpg
Het speciale tekeningtje onderaan:
Het lijkt op (8 ohms + 8 ohms in parallel) + (8 ohms in serieel) in parallel ?
Dus als ik dit uitreken dan zou ik komen op:
(4 hms) + (8 ohms) in parallel = 2.666 ohm
1
---------------
(1/4 + 1/8)
Net als parallel tekeningtje ? Klopt mijn berekening niet ? Wat doe ik fout ?
Is er misschien een andere bedrading mogelijk zodat deze op 2, 4 of 8 ohms uitkomt ?
Stel ik gebruik volledig parallel en een amplifier van 2 ohm ? Is de 2.666 ohm dan slecht voor de amplifier ?
Wat betreft de speciale bedrading zou dat problemen kunnen opleveren als de velden elkaar "cancellen".
Tot slot wat voor een amplifier zou geschikt zijn voor dit ding ?
(Speciaal tekeningtje was gemaakt aan de hand van deze beschrijving nummer 1:
"
This woofer is a triple voice coil 8 ohms woofer. There?are three pairs of connectors and each of them is 8 ohms.
1.
Ok, this is how to wire the woofer. Start with the closest two pair of connectors. You are going to connect the RED to RED and BLACK to Black "parallel connection". This will make the two 8 ohms coil one 4 ohms coil! Then connect the two combine "RED to RED" wire to the single BLACK wire of the third coil connector. The woofer is now configured for 2 ohms. This will leave you with two combine, BLACK to BLACK and a single RED wire. These two will be connected to the power amplifier. The combine RED to RED to BLACK wires?must be insulated and NOT connected to anything. This configuration is for use with a 8 oms power amplifier.
2.
For a 4 ohms amplifier, you would use this configuration. Starting with the closest two pair of connectors. Connect RED wire from connector/coil #1 to BLACK wire of connector/coil #2. Insulate these two wires! Then connect BLACK wire from connector/coil #3 to BLACK wire of connector/coil #1. Then connect RED wire from connector/coil #3 to RED wire of connector/coil #2. These? wire will be connected to the amplifier.
I measure 5 ohms on my DMM with this configuration.
"
)
Wie o wie kan mij helpen ?
Doei,
Skybuck.
Ik zit met deze subwoefer:
http://www.ecoustics.com/...um/home-audio/646685.html
Hij heeft drie aansluitingen elke voor een ("spreek"?) spoel van 8 ohm (voice-coil in het english).
Ik wil proberen deze aan te sluiten op een amplifier. De subwoefer heeft een specificatie van 210 RMS en werd waarschijnlijk aangedreven door 3 BASH amplifiers die 70 watts leverden (?).
De vraag is nu ten eerste hoe deze subwoefer aan te sluiten zodat de ohms een beetje kloppen ?
Ik heb zelf een serieel tekeningetje en een parallel tekeningetje gemaakt voor zover ik dit begrijp.
Tevens een "special wiring" tekeningtje gemaakt aan de hand van deze beschrijving:
http://forums.creative.com/archive/index.php?t-489341.html
De persoon in kwestie heeft het over een "2 ohms" configuratie geschikt voor een 8 ohms amplifier ? (HUH?)
En dat is gemeten met een digital multi meter, kan zijn dat mijn tekeningtje niet klopt:
Hier is mijn tekeningetje:
http://www.skybuck.org/Gi...rippleVoiceCoilWiring.jpg
Het speciale tekeningtje onderaan:
Het lijkt op (8 ohms + 8 ohms in parallel) + (8 ohms in serieel) in parallel ?
Dus als ik dit uitreken dan zou ik komen op:
(4 hms) + (8 ohms) in parallel = 2.666 ohm
1
---------------
(1/4 + 1/8)
Net als parallel tekeningtje ? Klopt mijn berekening niet ? Wat doe ik fout ?
Is er misschien een andere bedrading mogelijk zodat deze op 2, 4 of 8 ohms uitkomt ?
Stel ik gebruik volledig parallel en een amplifier van 2 ohm ? Is de 2.666 ohm dan slecht voor de amplifier ?
Wat betreft de speciale bedrading zou dat problemen kunnen opleveren als de velden elkaar "cancellen".
Tot slot wat voor een amplifier zou geschikt zijn voor dit ding ?
(Speciaal tekeningtje was gemaakt aan de hand van deze beschrijving nummer 1:
"
This woofer is a triple voice coil 8 ohms woofer. There?are three pairs of connectors and each of them is 8 ohms.
1.
Ok, this is how to wire the woofer. Start with the closest two pair of connectors. You are going to connect the RED to RED and BLACK to Black "parallel connection". This will make the two 8 ohms coil one 4 ohms coil! Then connect the two combine "RED to RED" wire to the single BLACK wire of the third coil connector. The woofer is now configured for 2 ohms. This will leave you with two combine, BLACK to BLACK and a single RED wire. These two will be connected to the power amplifier. The combine RED to RED to BLACK wires?must be insulated and NOT connected to anything. This configuration is for use with a 8 oms power amplifier.
2.
For a 4 ohms amplifier, you would use this configuration. Starting with the closest two pair of connectors. Connect RED wire from connector/coil #1 to BLACK wire of connector/coil #2. Insulate these two wires! Then connect BLACK wire from connector/coil #3 to BLACK wire of connector/coil #1. Then connect RED wire from connector/coil #3 to RED wire of connector/coil #2. These? wire will be connected to the amplifier.
I measure 5 ohms on my DMM with this configuration.
"
)
Wie o wie kan mij helpen ?
Doei,
Skybuck.
[ Voor 28% gewijzigd door Verwijderd op 28-07-2017 13:23 ]