[Debian] sym53c8xx parity errors

[Verwijderd]

Op mijn server waar op debian lenny/sid release draait, krijg ik bij het opstarten errors op mijn scsi drives. 1 drive (sda) pakt hij helemaal niet meer, en de andere sdb pakt hij nog wel, maar met veel parity fouten. Het gaat om twee harddisk, scsi ultra 3 hotswap. 1x maxtor en 1x seagate.

Systeem:

HP X4000 workstation
dual 2.4ghz XEON
1024MB ram

Dit is mijn dmesg log file van het booten van het systeem

code:

FEFEED4, 0074 (r1 HP     WOMBAT    6040000 PTL         8)
ACPI: DSDT 3FEFA0DE, 4DF6 (r1     HP   Wombat  6040000 MSFT  100000B)
ACPI: FACS 3FEFFFC0, 0040
ACPI: APIC 3FEFEF48, 0090 (r1 PTLTD  APIC    6040000  LTP        0)
ACPI: BOOT 3FEFEFD8, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x06] enabled)
Processor #6 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x07] enabled)
Processor #7 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfec80000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 32, address 0xfec80000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 2 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Built 1 zonelists.  Total pages: 259827
Kernel command line: root=/dev/sdb1 ro hwprobe=-pci sym53c8xx=mpar:n
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
mapped IOAPIC to ffffb000 (fec80000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2394.293 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1029300k/1047488k available (1655k kernel code, 17388k reserved, 636k data, 208k init, 129984k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4f000 - 0xfffff000   ( 704 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc0344000 - 0xc0378000   ( 208 kB)
      .data : 0xc029dfe5 - 0xc033d014   ( 636 kB)
      .text : 0xc0100000 - 0xc029dfe5   (1655 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4792.44 BogoMIPS (lpj=9584882)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: 3febfbff 00000000 00000000 00003080 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: Intel(R) XEON(TM) CPU 2.40GHz stepping 04
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4788.64 BogoMIPS (lpj=9577298)
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: 3febfbff 00000000 00000000 00003080 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) XEON(TM) CPU 2.40GHz stepping 04
SMP alternatives: switching to SMP code
Booting processor 2/6 eip 3000
Initializing CPU#2
Calibrating delay using timer specific routine.. 4788.73 BogoMIPS (lpj=9577478)
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After all inits, caps: 3febfbff 00000000 00000000 00003080 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: Intel P4/Xeon Extended MCE MSRs (12) available
CPU2: Thermal monitoring enabled
CPU2: Intel(R) XEON(TM) CPU 2.40GHz stepping 04
SMP alternatives: switching to SMP code
Booting processor 3/7 eip 3000
Initializing CPU#3
Calibrating delay using timer specific routine.. 4788.72 BogoMIPS (lpj=9577458)
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After all inits, caps: 3febfbff 00000000 00000000 00003080 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel P4/Xeon Extended MCE MSRs (12) available
CPU3: Thermal monitoring enabled
CPU3: Intel(R) XEON(TM) CPU 2.40GHz stepping 04
Total of 4 processors activated (19158.55 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Brought up 4 CPUs
migration_cost=142,679
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd91b, last bus=4
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH4 GPIO
Boot video device is 0000:01:00.0
PCI: Firmware left 0000:04:0d.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HLB_.P64H._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SLOT._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 9 10 11 14 15) *5
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 14 15) *12
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: f4000000-f48fffff
  PREFETCH window: f6000000-f7ffffff
PCI: Bridge: 0000:02:1f.0
  IO window: 2000-2fff
  MEM window: f4900000-f49fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
  IO window: 2000-2fff
  MEM window: f4900000-f49fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: 3000-3fff
  MEM window: f4a00000-f4afffff
  PREFETCH window: 50000000-500fffff
PCI: Setting latency timer of device 0000:02:1f.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5453k freed
Simple Boot Flag at 0x3e set to 0x1
audit: initializing netlink socket (disabled)
audit(1190144635.324:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MOUS] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI No-Shortcut mode
Freeing unused kernel memory: 208k freed
input: AT Translated Set 2 keyboard as /class/input/input0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 16, io base 0x000010c0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
SCSI subsystem initialized
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
ICH2: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:03:08.0[A] -> GSI 23 (level, low) -> IRQ 17
ICH2: chipset revision 4
ICH2: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x10e0-0x10e7, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x10e8-0x10ef, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
sym0: <1010-66> rev 0x1 at pci 0000:03:08.0 irq 17
sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: handling phase mismatch from SCRIPTS.
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.3
 target0:0:0: Scan at boot disabled in NVRAM
Probing IDE interface ide1...
hdc: GCR-8481B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
scsi 0:0:1:0: Direct-Access     SEAGATE  ST318406LC       8A03 PQ: 0 ANSI: 3
 target0:0:1: tagged command queuing enabled, command queue depth 16.
 target0:0:1: Beginning Domain Validation
 target0:0:1: asynchronous
 target0:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
sym0: SCSI parity error detected: SCR1=3 DBC=15000000 SBCL=2d
 target0:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
 target0:0:1: Domain Validation detected failure, dropping back
 target0:0:1: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 62)
sym0: SCSI parity error detected: SCR1=3 DBC=15000000 SBCL=2d
 target0:0:1: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 62)
 target0:0:1: Domain Validation detected failure, dropping back
 target0:0:1: FAST-40 WIDE SCSI 66.0 MB/s DT (30.3 ns, offset 62)
sym0: SCSI parity error detected: SCR1=3 DBC=15000000 SBCL=2d
 target0:0:1: FAST-40 WIDE SCSI 66.0 MB/s DT (30.3 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=1500000e SBCL=ae
 target0:0:1: Domain Validation detected failure, dropping back
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: Domain Validation detected failure, dropping back
 target0:0:1: FAST-20 WIDE SCSI 38.4 MB/s DT (52 ns, offset 62)
sym0: SCSI parity error detected: SCR1=3 DBC=15000000 SBCL=2d
 target0:0:1: FAST-20 WIDE SCSI 38.4 MB/s DT (52 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=1500000e SBCL=ae
 target0:0:1: Domain Validation detected failure, dropping back
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: Domain Validation detected failure, dropping back
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=3 DBC=11000000 SBCL=29
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: Domain Validation detected failure, dropping back
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: Domain Validation detected failure, dropping back
sym0: SCSI parity error detected: SCR1=3 DBC=11000000 SBCL=29
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: Domain Validation detected failure, dropping back
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: Domain Validation detected failure, dropping back
sym0: SCSI parity error detected: SCR1=3 DBC=11000000 SBCL=29
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: Domain Validation detected failure, dropping back
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: Domain Validation Failure, dropping back to Asynchronous
 target0:0:1: Domain Validation skipping write tests
 target0:0:1: Ending Domain Validation
sym0: SCSI parity error detected: SCR1=3 DBC=11000ff0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sym0: SCSI parity error detected: SCR1=3 DBC=11000ff0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sym0: SCSI parity error detected: SCR1=3 DBC=11000ff0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sym0: SCSI parity error detected: SCR1=3 DBC=11000ff0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sym0: SCSI parity error detected: SCR1=3 DBC=11000ff0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sym0: SCSI parity error detected: SCR1=3 DBC=11000ff0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sym0: SCSI parity error detected: SCR1=1 DBC=11000000 SBCL=29
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sym0: SCSI parity error detected: SCR1=1 DBC=11000000 SBCL=29
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
scsi 0:0:2:0: Direct-Access     MAXTOR   ATLAS10K4_36SCA  DFM0 PQ: 0 ANSI: 3
 target0:0:2: tagged command queuing enabled, command queue depth 16.
 target0:0:2: Beginning Domain Validation
 target0:0:2: asynchronous
 target0:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d
 target0:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=1500000e SBCL=ae
 target0:0:2: Domain Validation detected failure, dropping back
 target0:0:2: control msgout: c.
sym0: TARGET 2 has been reset.
 target0:0:2: Domain Validation detected failure, dropping back
 target0:0:2: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d
 target0:0:2: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=1500000e SBCL=ae
 target0:0:2: Domain Validation detected failure, dropping back
 target0:0:2: control msgout: c.
sym0: TARGET 2 has been reset.
 target0:0:2: Domain Validation detected failure, dropping back
 target0:0:2: FAST-20 WIDE SCSI 26.4 MB/s DT (76 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d
 target0:0:2: FAST-20 WIDE SCSI 26.4 MB/s DT (76 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=1500000e SBCL=ae
 target0:0:2: Domain Validation detected failure, dropping back
 target0:0:2: control msgout: c.
sym0: TARGET 2 has been reset.
 target0:0:2: Domain Validation detected failure, dropping back
 target0:0:2: FAST-10 WIDE SCSI 12.0 MB/s DT (168 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=f21c0004 SBCL=2d
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
 target0:0:2: Domain Validation detected failure, dropping back
 target0:0:2: FAST-5 WIDE SCSI 10.0 MB/s DT (200 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=f21c0004 SBCL=2d
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
 target0:0:2: Domain Validation detected failure, dropping back
 target0:0:2: FAST-5 WIDE SCSI 10.0 MB/s DT (200 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=f21c0004 SBCL=2d
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
 target0:0:2: Domain Validation detected failure, dropping back
 target0:0:2: FAST-5 WIDE SCSI 10.0 MB/s DT (200 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=f21c0004 SBCL=2d
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
 target0:0:2: Domain Validation detected failure, dropping back
 target0:0:2: FAST-5 WIDE SCSI 10.0 MB/s DT (200 ns, offset 62)
sym0: SCSI parity error detected: SCR1=1 DBC=f21c0004 SBCL=2d
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
 target0:0:2: Domain Validation Failure, dropping back to Asynchronous
 target0:0:2: wide asynchronous
 target0:0:2: Ending Domain Validation
 target0:0:3: Scan at boot disabled in NVRAM
 target0:0:4: Scan at boot disabled in NVRAM
 target0:0:5: Scan at boot disabled in NVRAM
 target0:0:6: Scan at boot disabled in NVRAM
 target0:0:8: Scan at boot disabled in NVRAM
 target0:0:9: Scan at boot disabled in NVRAM
 target0:0:10: Scan at boot disabled in NVRAM
 target0:0:11: Scan at boot disabled in NVRAM
 target0:0:12: Scan at boot disabled in NVRAM
 target0:0:13: Scan at boot disabled in NVRAM
 target0:0:14: Scan at boot disabled in NVRAM
 target0:0:15: Scan at boot disabled in NVRAM
ACPI: PCI Interrupt 0000:03:08.1[B] -> GSI 19 (level, low) -> IRQ 16
sym1: <1010-66> rev 0x1 at pci 0000:03:08.1 irq 16
sym1: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: handling phase mismatch from SCRIPTS.
sym1: SCSI BUS has been reset.
scsi1 : sym-2.2.3
 target1:0:0: Scan at boot disabled in NVRAM
 target1:0:1: Scan at boot disabled in NVRAM
 target1:0:2: Scan at boot disabled in NVRAM
 target1:0:3: Scan at boot disabled in NVRAM
 target1:0:4: Scan at boot disabled in NVRAM
 target1:0:5: Scan at boot disabled in NVRAM
 target1:0:6: Scan at boot disabled in NVRAM
 target1:0:8: Scan at boot disabled in NVRAM
 target1:0:9: Scan at boot disabled in NVRAM
 target1:0:10: Scan at boot disabled in NVRAM
 target1:0:11: Scan at boot disabled in NVRAM
 target1:0:12: Scan at boot disabled in NVRAM
 target1:0:13: Scan at boot disabled in NVRAM
 target1:0:14: Scan at boot disabled in NVRAM
 target1:0:15: Scan at boot disabled in NVRAM
ACPI: PCI Interrupt 0000:04:0d.0[A] -> GSI 21 (level, low) -> IRQ 18
e100: eth0: e100_probe: addr 0xf4a00000, irq 18, MAC addr 00:E0:81:00:99:8B
ACPI: PCI Interrupt 0000:04:09.0[A] -> GSI 19 (level, low) -> IRQ 16
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:04:09.0: 3Com PCI 3c905B Cyclone 100baseTx at f8848000.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
hdc: ATAPI 48X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
udev: renamed network interface eth1 to eth0
udev: renamed network interface eth0_rename to eth1
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sda: Unit Not Ready, error = 0xb0002
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sda : READ CAPACITY failed.
sda : status=1, message=00, host=11, driver=00 
sda : sense not available. 
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sda: test WP failed, assume Write Enabled
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sda: asking for cache data failed
sda: assuming drive cache: write through
sd 0:0:1:0: Attached scsi disk sda
SCSI device sdb: 71132959 512-byte hdwr sectors (36420 MB)
sdb: Write Protect is off
sdb: Mode Sense: ed 00 10 08
SCSI device sdb: write cache: disabled, read cache: enabled, supports DPO and FUA
SCSI device sdb: 71132959 512-byte hdwr sectors (36420 MB)
sdb: Write Protect is off
sdb: Mode Sense: ed 00 10 08
SCSI device sdb: write cache: disabled, read cache: enabled, supports DPO and FUA
 sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 sdb8 sdb9 >
sd 0:0:2:0: Attached scsi disk sdb
sym0: SCSI parity error detected: SCR1=3 DBC=110000f0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sym0: SCSI parity error detected: SCR1=3 DBC=110000f0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sym0: SCSI parity error detected: SCR1=3 DBC=1100006e SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sym0: SCSI parity error detected: SCR1=3 DBC=110000f0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
sym0: SCSI parity error detected: SCR1=3 DBC=110000f0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
input: PC Speaker as /class/input/input1
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
intel_rng: FWH not detected
Real Time Clock Driver v1.12ac
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 19
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel i860 Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
Intel 810 + AC97 Audio, version 1.01, 17:36:31 May 30 2007
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.5 to 64
i810: Intel ICH2 found at IO 0x1080 and 0x1400, MEM 0x0000 and 0x0000, IRQ 19
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
sym0: SCSI parity error detected: SCR1=3 DBC=110000f0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
EDAC MC: Ver: 2.0.1 May 30 2007
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: ADS96 (Analog Devices AD1885)
i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not present), total channels = 2
EDAC i82860: i82860 init one
EDAC MC0: Giving out device to i82860_edac i82860: DEV 0000:00:00.0
sym0: SCSI parity error detected: SCR1=3 DBC=1100006e SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
sym0: SCSI parity error detected: SCR1=3 DBC=110000f0 SBCL=ae
 target0:0:1: wide asynchronous
sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 target0:0:1: control msgout: c.
sym0: TARGET 1 has been reset.
Adding 2650684k swap on /dev/sdb7.  Priority:-1 extents:1 across:2650684k
EXT3 FS on sdb1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [e-mail]
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NET: Registered protocol family 15
e100: eth1: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0:  setting half-duplex.
padlock: VIA PadLock not detected.
padlock: VIA PadLock Hash Engine not detected.
padlock: VIA PadLock Hash Engine not detected.
padlock: No VIA PadLock drivers have been loaded.
Initializing XFRM netlink socket

Wat ik al geprobeerd heb:

• Booten met hwprobe=-pci
• Booten met sym53c8xx=mpar:n
• SCSI configuratie controleren

Maar dit alles helpt niet, en de fouten blijven gewoon. Mijn kernel regel in grub heb ik aangepast op deze manier voor de opties mee te geven, ik weet niet zeker of dit helemaal goed is

code:

root            (hd1,0)
kernel          /boot/vmlinuz-2.6.21.3 root=/dev/sdb1 ro hwprobe=-pci sym53c8xx=mpar:n
initrd          /boot/initrd.img-2.6.21.3

Iemand een idee wat er mis gaat, of zit er hardware tussen wat gaar is ?

[SambalBij]

Zou gare hardware kunnen zijn, de kaart zelf of een van de schijven. Controleer de bekabeling eens, inclusief ook de terminator.
Je kunt anders eens proberen wat ie doet als je een van de schijven loshaalt. Ik zou die sda eens loshalen en kijken of ie dan sdb wel zonder fouten kan benaderen. (de root staat op sdb zo te zien? kun je dan booten zonder sda? anders eens van een cd booten en kijken of de aangesloten schijf dan te benaderen is)

[Verwijderd]

SambalBij schreef op woensdag 19 september 2007 @ 00:18:
Zou gare hardware kunnen zijn, de kaart zelf of een van de schijven. Controleer de bekabeling eens, inclusief ook de terminator.
Je kunt anders eens proberen wat ie doet als je een van de schijven loshaalt. Ik zou die sda eens loshalen en kijken of ie dan sdb wel zonder fouten kan benaderen. (de root staat op sdb zo te zien? kun je dan booten zonder sda? anders eens van een cd booten en kijken of de aangesloten schijf dan te benaderen is)

Dat is inderdaad wel een idee om ze even appart te testen, als ik ze vanuit de scsi bios verify, geven ze geen problemen.

De schijven zijn SCA 80, en ik heb ze dmv een convertor die uit mijn oude compaq DL380 kwam aangesloten, dwz een print waar 4 x SCA80 aan 1 kan zit en aan de andere kant 1x scsi III 68pins, misschien dat dit ook de nodige problemen veroorzaakt, en kan ik beter losse convertors kopen ???

[killercow]

Hoe oud is die scsi kaart?
Want de nieuwe kernels hebben ruzie met de oude megaraid en symbios kaartjes.
Debian 3.* doet het nog wel, 4.0 niet meer.

[Verwijderd]

killercow schreef op woensdag 19 september 2007 @ 11:24:
Hoe oud is die scsi kaart?
Want de nieuwe kernels hebben ruzie met de oude megaraid en symbios kaartjes.
Debian 3.* doet het nog wel, 4.0 niet meer.

Geen idee hoe oud precies eigelijk, maar het is een SYM53C1010R onboard bij die X4000 van HP dus denk ergens rond 2002 ofzo. Mijn kernel is 2.6.21.

[ Voor 4% gewijzigd door Verwijderd op 19-09-2007 12:35 ]