[FC5] Ipod shuffle

[stokvis79]

Ik heb een Ipod Shuffle gehad, deze wordt alleen niet herkent door FC5.

Mijn andere usb-pennentjes worden prima herkent en direct gemount. Alleen mijn Ipod-je wordt niet herkent, als ik met de Ipod, reeds aangesloten, probeer te booten dan blijft het bootproces hangen na het starten van bluetooth diensten.

Heeft iemand misschien een idee waar dat aan zou kunnen liggen? De Ipod is fat16 geformateerd als ik me niet vergis, ik heb hem al eens succesvol gemount vanuit Damn Small Linux.

kernel: 2.6.16-1.2111_FC5
mobo: KT3 Ultra2

[ Voor 3% gewijzigd door stokvis79 op 17-05-2006 17:59 ]

[Verwijderd]

Post de output van dmesg en /var/log/messages eens na het insteken van de iPod Shuffle?

[stokvis79]

dmesg:

code:

Linux version 2.6.16-1.2111_FC5 ([e-mail]) (gcc version 4.1.0 20060304 (Red Hat 4.1.0-3)) #1 Thu May 4 21:16:58 EDT 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d0000 - 00000000000d6000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
 BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
 BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
895MB LOWMEM available.
found SMP MP-table at 000fb940
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 262128
  DMA zone: 4096 pages, LIFO batch:0
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 225279 pages, LIFO batch:31
  HighMem zone: 32753 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 AMI                                   ) @ 0x000fa8e0
ACPI: RSDT (v001 AMIINT VIA_K7   0x00000010 MSFT 0x00000097) @ 0x3fff0000
ACPI: FADT (v001 AMIINT VIA_K7   0x00000011 MSFT 0x00000097) @ 0x3fff0030
ACPI: MADT (v001 AMIINT VIA_K7   0x00000009 MSFT 0x00000097) @ 0x3fff00c0
ACPI: DSDT (v001    VIA   VIA_K7 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:6 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c03d5000 soft=c03d4000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1667.058 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034576k/1048512k available (1918k kernel code, 13268k reserved, 775k data, 176k init, 131012k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3338.90 BogoMIPS (lpj=6677815)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f3ff c1c3fbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 2000+ stepping 02
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 899k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by vt8235 PM
PCI quirk: region 0400-040f claimed by vt8235 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: dbe00000-dfefffff
  PREFETCH window: bbc00000-dbcfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1147892361.988:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 9227B3BCB5EBAE
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU1] (supports 16 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:03: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 15
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD2500JB-00GVC0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: _NEC DVD_RW ND-2510A, ATAPI CD/DVD-ROM drive
hdd: CD-RW CDR-5S40, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda4 < hda5 hda6 hda7 hda8 hda9 >
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X CD-ROM CD-R/RW drive, 1984kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Processor cpuid 662 not supported
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 UAR1 USB1 USB2 USB3 EHCI  USB USBA USBB  AC9  MC9 ILAN SLPB
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 176k freed
Write protecting the kernel read-only data: 359k
input: ImExPS/2 Generic Explorer Mouse as /class/input/input1
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security:  3 users, 7 roles, 1220 types, 147 bools, 1 sens, 256 cats
security:  56 classes, 40498 rules
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev hda8, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 16
eth0: RealTek RTL8139 at 0xf8806f00, 00:50:fc:c3:c8:d3, IRQ 16
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
NET: Registered protocol family 23
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 17
Model 100a Rev 00000000 Serial 100a1102
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 18
NVRM: loading NVIDIA Linux x86 Kernel Module  1.0-8756  Wed Mar 29 14:26:26 PST 2006
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:10.3, from 5 to 3
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: irq 19, io mem 0xdffffe00
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 3
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 19, io base 0x0000dc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:10.1, from 5 to 3
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 19, io base 0x0000e000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 3
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 19, io base 0x0000e400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: not running at top speed; connect to a high speed hub
usb 2-1: configuration #1 chosen from 1 choice
hiddev96: USB HID v1.00 Device [Yealink Network Technology Ltd. VOIP USB Phone          ] on usb-0000:00:10.0-1
usb 3-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
usbcore: registered new driver snd-usb-audio
Linux video capture interface: v1.00
sn9c102: V4L2 driver for SN9C10x PC Camera Controllers v1:1.26
usb 3-2: SN9C10[12] PC Camera Controller detected (vid/pid 0x0C45/0x6009)
usb 3-2: PAS106B image sensor detected
usb 3-2: Initialization succeeded
usb 3-2: V4L2 device registered as /dev/video0
usbcore: registered new driver sn9c102
Non-volatile memory driver v1.2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
parport0: Printer, HEWLETT-PACKARD DESKJET 720C
lp0: using parport0 (interrupt-driven).
lp0: console ready
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: [e-mail]
EXT3 FS on hda8, internal journal
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda9, type ext3), uses xattr
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda7, type ext3), uses xattr
SELinux: initialized (dev hda1, type vfat), uses genfs_contexts
SELinux: initialized (dev hda6, type vfat), uses genfs_contexts
Adding 1044184k swap on /dev/hda5.  Priority:-1 extents:1 across:1044184k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8191 buckets, 65528 max) - 232 bytes per conntrack
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.7
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
eth0: no IPv6 routers present
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
audit(1147888288.335:2): avc:  denied  { use } for  pid=2655 comm="bluez-pin" name="[8091]" dev=pipefs ino=8091 scontext=user_u:system_r:bluetooth_helper_t:s0 tcontext=system_u:system_r:xdm_t:s0-s0:c0.c255 tclass=fd
audit(1147888288.339:3): avc:  denied  { use } for  pid=2655 comm="bluez-pin" name="[8091]" dev=pipefs ino=8091 scontext=user_u:system_r:bluetooth_helper_t:s0 tcontext=system_u:system_r:xdm_t:s0-s0:c0.c255 tclass=fd
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
SELinux: initialized (dev hdc, type iso9660), uses genfs_contexts
usb 1-3: new high speed USB device using ehci_hcd and address 4

/var/log/messages

code:

May 17 19:52:22 localhost kernel: usb 1-3: new high speed USB device using ehci_hcd and address 4

[Superboer12]

doe eens 'cat /proc/scsi/scsi' als je hem eraan hebt hangen.
Als het goed is moet hij daar verschijnen. Zo niet doe dan ook eens 'cat /proc/bus/usb/devices'.

Als hij er (bij) staat kun je hem mounten met 'mount /dev/sda /jemountpoint' (als root).
Wanneer je meerdere scsi/sata apparaten hebt dan moet je sda veranderen in sdb, sdc etc.

[ Voor 7% gewijzigd door Superboer12 op 18-05-2006 11:22 . Reden: tikfoutje ]

[stokvis79]

cat /proc/scsi/scsi geeft na het aankoppelen van mijn 'normale' usb-pen de eerste melding. Na het loskoppelen en het daarop volgende aankoppelen van mn Ipod geeft de 2de melding:

code:

[root@localhost drik]# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
  Vendor: USB 2.0  Model: Flash Disk       Rev: 2.00
  Type:   Direct-Access                    ANSI SCSI revision: 02
[root@localhost drik]# cat /proc/scsi/scsi
Attached devices:
[root@localhost drik]#

cat /proc/bus/usb/devices, doet niks ik krijg geen output.

Ik kan me herinneren dat ik ergens eens een 'error -71' vaut gezien heb, alleen weet ik niet meer waar. Als ik google op die error 71, vind ik een suggestie om udev aan te passen.

dat gaat om deze tread.

Is dit verstandig, ik ben nml bang dat ik straks mn systeempje om zeep help oid

[Superboer12]

Probeer het anders eens zonder je Bluetooth dongle. (ik ga ervan uit dat je zo'n ding hebt omdat je bluetooth diensten start)

[stokvis79]

Ik heb geen dongle, FC5 start alleen wel de bluetooth diensten die heb ik nu uitgeschakeld en een keer gereboot.

mn podje weer in geplugd, en zie hier mijn /var/log/messages

code:

May 20 08:31:47 localhost kernel: usb 4-3: configuration #1 chosen from 2 choices
May 20 08:31:47 localhost kernel: usb 4-3: can't set config #1, error -71
May 20 08:31:47 localhost kernel: usb 4-3: USB disconnect, address 3
May 20 08:31:47 localhost kernel: usb 1-1: new full speed USB device using uhci_hcd and address 3
May 20 08:31:47 localhost kernel: usb 1-1: not running at top speed; connect to a high speed hub
May 20 08:31:47 localhost kernel: usb 1-1: configuration #1 chosen from 1 choice
May 20 08:31:47 localhost kernel: hiddev96: USB HID v1.00 Device [Yealink Network Technology Ltd. VOIP USB Phone           ] on usb-0000:00:10.0-1
May 20 08:31:48 localhost kernel: usb 2-2: new full speed USB device using uhci_hcd and address 2
May 20 08:31:48 localhost kernel: usb 2-2: configuration #1 chosen from 1 choice
May 20 08:31:48 localhost kernel: usbcore: registered new driver snd-usb-audio
May 20 08:31:48 localhost kernel: Linux video capture interface: v1.00
May 20 08:31:48 localhost kernel: sn9c102: V4L2 driver for SN9C10x PC Camera Controllers v1:1.26
May 20 08:31:48 localhost kernel: usb 2-2: SN9C10[12] PC Camera Controller detected (vid/pid 0x0C45/0x6009)
May 20 08:31:48 localhost kernel: usb 2-2: PAS106B image sensor detected
May 20 08:31:48 localhost kernel: usb 2-2: Initialization succeeded
May 20 08:31:48 localhost kernel: usb 2-2: V4L2 device registered as /dev/video0
May 20 08:31:48 localhost kernel: usbcore: registered new driver sn9c102
May 20 08:31:55 localhost kernel: usb 4-3: new high speed USB device using ehci_hcd and address 5

Nu weet ik waar ik die error 71 message gezien heb. (regel 2)