Heb een usermanual gevonden hieronder enkele stukjes:
Thank you for choosing the MS-7091 v1.X Micro ATX
mainboard. The MS-7091 v1.X mainboard is based on Intel® 915P
and Intel® ICH6R chipset for optimal system efficiency. Designed to
fit the advanced Intel® Pentium Prescott LGA775 processor, the
MS-7091 v1.X mainboard delivers a high performance and professional
desktop platform solution.
CPU
-- Supports Intel® Pentium 4 Prescott LGA775 processors
-- Supports up to Pentium 4 3XX, 5XX sequence processor
-- Supports Intel Hyper-Threading Technology.
Chipset
-- Intel® 915P chipset
- Supports FSB 533/800MHz.
- Supports DDR 400/333 memory interface.
-- Intel® ICH6R chipset
- Hi-Speed USB (USB2.0) controller, 480Mb/sec, up
- 4 Serial ATA ports with transfer rate up to 150 Mbytes/
- 1 channel Ultra ATA 100 bus Master IDE controller.
- PCI Master v2.3, I/O APIC.
- ACPI 2.0 Compliant.
- Serial ATA 150 RAID 0, RAID 1 and Matrix RAID.
- Integrated AHCI controller.
Main Memory
-- Supports four DDR1 SDRAM memory modules.
-- Supports up to 4GB memory size.
-- Supports Dual channel DDR1.
Slots
-- One PCI Express x16 slot (supports PCI Express Bus
-- Three 32-bit v2.3 Master PCI bus slots (support 3.3v/
- The second PCI slot (PCI2, in blue color) supports
On-Board IDE
-- One Ultra DMA 66/100 IDE controllers integrated in
- Supports PIO, Bus Master operation modes.
- Can connect up to Two Ultra ATA drives.
-- Serial ATA 150 controller integrated in ICH6R.
- Up to 150MB/sec transfer speed.
- Can connect up to four Serial ATA devices.
On-Board Peripherals
-- On-Board Peripherals include:
- 1 floppy port supports 1 FDD with 360K, 720K, 1.2M,
- 1 serial port
- 1 parallel port supports SPP/EPP/ECP mode
- 8 USB 2.0 / 1.1 ports (Rear*4 / Front*4)
- 1 RJ45 connector
- 1 Rear 1394 port (6 Pins) / 1 Front 1394 port
The mainboard provides 4 slots for 184-pin DDR SDRAM DIMM (Double In-
Line Memory Module) modules and supports the memory size up to 4GB. You can
install DDR400/DDR333 modules on the DDR DIMM slots (DIMM 1~4).
Memory
DDR DIMM Slots
(DIMM 1~4)
Introduction to DDR SDRAM
DDR (Double Data Rate) SDRAM is similar to conventional SDRAM, but doubles
the rate by transferring data twice per cycle. It uses 2.5 volts as opposed to 3.
3 volts used in SDR SDRAM, and requires 184-pin DIMM modules rather than 168-pin
DIMM modules used by SDR SDRAM. Please note that the DDR SDRAM does not
support ECC (error correcting code) and registered DIMM.
DDR Population Rules
Install at least one DIMM module on the slots. Each DIMM slot supports up to a
maximum size of 1GB. Users can install either single- or double-sided modules to
meet their own needs. Please note that each DIMM can work respectively for
single-channel DDR, but there are some rules while using dual-channel
DDR (Please refer to the suggested DDR population table on p.2-8). Users may install
memory modules of different type and density on different-channel DDR DIMMs.
However, the same type and density memory modules are necessary
while using dual-channel DDR, or instability may happen.
MS-7091 M-ATX Mainboard
MSI Reminds You...
Dual-channel DDR works ONLY in the 3 combinations listed in the
table below.
Please refer to the following table for detailed dual-channel DDR. Other combination
not listed below will function as single-channel DDR.
DIMM1 (ChA)-------DIMM2 (ChA)-----DIMM3 (ChB)-------DIMM4 (ChB)-----System Density
128MB~1GB---------------------------------128MB~1GB ---------------------------------256MB~2GB
---------------------------128MB~1GB -------------------------------128MB~1GB -------256MB~2GB
128MB~1GB--------128MB~1GB -----128MB~1GB -------128MB~1GB------- 512MB~4GB
[
Voor 8% gewijzigd door
Anoniem: 151315 op 05-08-2005 23:50
]